Disturbing loads identification in power systems: a single-point time-domain method based on IEEE 1459-2000

Risultato della ricerca: Article

22 Citazioni (Scopus)

Abstract

This paper presents a single-point method for the identification of prevailing disturbing loads in power systems for both single-phase and the three-phase applications downstream or upstream the metering section. It is based on the simultaneous measurement of three non-active power quantities, which are based on the IEEE Std. 1459-2000 approach. The proposed method is based only on the separation of the fundamental components from the harmonic content of voltage and current, thus it does not require any spectral analysis of voltages and current. In the paper, the formulation of the proposed method and its time-domain implementation are described; moreover, some simulation results are presented and discussed, showing the effectiveness of the method both in the absence and in the presence of the measurement transducers.
Lingua originaleEnglish
pagine (da-a)1436-1445
Numero di pagine10
RivistaIEEE Transactions on Instrumentation and Measurement
Volume58
Stato di pubblicazionePublished - 2009

Fingerprint

Electric potential
electric potential
Spectrum analysis
upstream
spectrum analysis
Transducers
transducers
harmonics
formulations
simulation

All Science Journal Classification (ASJC) codes

  • Instrumentation
  • Electrical and Electronic Engineering

Cita questo

@article{df05bfcd5e69480a99f560e9bf4bfd60,
title = "Disturbing loads identification in power systems: a single-point time-domain method based on IEEE 1459-2000",
abstract = "This paper presents a single-point method for the identification of prevailing disturbing loads in power systems for both single-phase and the three-phase applications downstream or upstream the metering section. It is based on the simultaneous measurement of three non-active power quantities, which are based on the IEEE Std. 1459-2000 approach. The proposed method is based only on the separation of the fundamental components from the harmonic content of voltage and current, thus it does not require any spectral analysis of voltages and current. In the paper, the formulation of the proposed method and its time-domain implementation are described; moreover, some simulation results are presented and discussed, showing the effectiveness of the method both in the absence and in the presence of the measurement transducers.",
keywords = "power measurements, harmonic distortion, reactive power, power systems, power definitions, power quality, IEEE 1459",
author = "Antonio Cataliotti and Valentina Cosentino",
year = "2009",
language = "English",
volume = "58",
pages = "1436--1445",
journal = "IEEE Transactions on Instrumentation and Measurement",
issn = "0018-9456",
publisher = "Institute of Electrical and Electronics Engineers Inc.",

}

TY - JOUR

T1 - Disturbing loads identification in power systems: a single-point time-domain method based on IEEE 1459-2000

AU - Cataliotti, Antonio

AU - Cosentino, Valentina

PY - 2009

Y1 - 2009

N2 - This paper presents a single-point method for the identification of prevailing disturbing loads in power systems for both single-phase and the three-phase applications downstream or upstream the metering section. It is based on the simultaneous measurement of three non-active power quantities, which are based on the IEEE Std. 1459-2000 approach. The proposed method is based only on the separation of the fundamental components from the harmonic content of voltage and current, thus it does not require any spectral analysis of voltages and current. In the paper, the formulation of the proposed method and its time-domain implementation are described; moreover, some simulation results are presented and discussed, showing the effectiveness of the method both in the absence and in the presence of the measurement transducers.

AB - This paper presents a single-point method for the identification of prevailing disturbing loads in power systems for both single-phase and the three-phase applications downstream or upstream the metering section. It is based on the simultaneous measurement of three non-active power quantities, which are based on the IEEE Std. 1459-2000 approach. The proposed method is based only on the separation of the fundamental components from the harmonic content of voltage and current, thus it does not require any spectral analysis of voltages and current. In the paper, the formulation of the proposed method and its time-domain implementation are described; moreover, some simulation results are presented and discussed, showing the effectiveness of the method both in the absence and in the presence of the measurement transducers.

KW - power measurements, harmonic distortion, reactive power, power systems, power definitions, power quality, IEEE 1459

UR - http://hdl.handle.net/10447/39070

UR - http://ieeexplore.ieee.org/document/4787046/

M3 - Article

VL - 58

SP - 1436

EP - 1445

JO - IEEE Transactions on Instrumentation and Measurement

JF - IEEE Transactions on Instrumentation and Measurement

SN - 0018-9456

ER -